Install Curtain Rods

Just when you thought it was safe to look forward to the weekend, you realize that this was the weekend you were buying and hanging curtains. Well, not to worry, it's easy to do, and won't take nearly as long as you thought. We'll show you how and what to hang and how to make the process go smoothly. Just get started with Step 1 below.

Steps

Setting Up for Success

1. Buy your curtains. You'll want to decide what style of curtain is right for you, if you have not yet purchased your curtains and curtain rods. There are a number of styles, each giving your room a different flavor and functioning in a slightly different way. Some of your options include:
   • Drapes are typically made from heavy material and are pleated, which requires a traverse rod. To hang, you must place drapery pins in the pleat, and then hang them on the rod. A cord allows you to pull the drapes open and closed.
   • Panel curtains, eyelet curtains and tab top curtains are meant to hang from a plain round rod. They may have a pocket along the top to push the rod through, or the rod may be threaded through eyelets or tabs. Panel curtains may end at the top or bottom of the windowsill, extend to the floor, or be even longer—a style known as puddling.
   • Cafe curtains cover only the bottom half of a window, to let light into the room while affording some privacy. They are popular on kitchen windows and are typically hung on rods installed inside the window frame on tension rods.
   • Door panels have pockets on the top and bottom and require 2 curtain rods, which you install on a door or simply attach with magnets. Door panels are often used on french doors and sidelights.
2. Decide where you want the bottom of your curtain to fall. When buying curtains, keep in mind that their length should cover the entire window (unless they are cafe curtains). If you buy tab top curtains, make sure the curtain length doesn't include the length of the tabs.
   • Floor length curtains end 1/2 inch (1.25 cm) from the floor unless you live in a humid environment, in which case they should end 1 inch (2.5 cm) from the floor, because they will stretch more on humid days. If you plan to puddle your curtains, you only need to ensure you have plenty of material left over for the puddle.
   • Curtains that hang below the sill should extend 4 inches (10 cm) below the sill, long enough to cover the edge of the casing below the window.
   • Sill-length curtains should skim the sill.
3. Consider how far you want to be able to draw back the curtains. If you'd like to pull them completely away from the window, buy a longer rod or a rod that has a return (a 90-degree turn on each end that allows you to push the curtain around the turn or rest against the wall). The length of the return should depend on the type and width of the curtain.
4. Choose whether to install the rod on the casing or the wall outside the casing. Installing in the casing will always leave at least part of the window obscured, while installing outside the casing allows you to pull the curtains back completely. Which you choose will partially be determined by the style and look you want, but you may also have to account for the material of the wall or casing. If you have plastic window casing, the curtain rods will need to be installed on the wall. If you have plaster, cob, or stone walls, then the casing may be easier.
   • Bear in mind that the curtain will only draw back as far as the brackets holding the curtain rod, whether or not you have a return, and the style of the curtain will determine how much they can be compressed. The amount you can compress a curtain is called the stack back.
   • You may want to keep part of the window covered even when the curtains are open, or you may prefer to completely expose the window to let as much light into the room as possible.

Installing Correctly

1. Measure for the height of the rod. Use a measuring tape. Determine where the top of the curtain will be from where you want the curtain to end: at the sill, below the sill or on the floor. Bear in mind that some styles of curtains have ruffles or pleats that extend above the top of the rod; subtract this section from the measurement. Mark this point on both sides of casing or wall with a pencil. Use a laser level to make sure your marks are even.
2. Mark where the brackets will go. When you're sure of all your measurements, use a pencil to mark where the screws will go. Be careful not to get too close to the edge if installing in the casing, as this will make the material too fragile and cause the wood to crack.
3. Add a mid brace if needed. Consider the length of the rod when hanging the brackets. Though most curtain rods are adjustable, you don't want the distance between the brackets to be so wide that the rod sags in the middle. In general, you shouldn't increase the length of the expanded  rod by more than 50 percent.
4. Drill pilot holes to help start the screws. This can keep the screws from cracking the casing or wall material. If installing the brackets on the wall, make sure your pilot holes are big enough to place the screw anchors into, if you need to use screw anchors.
   • Screw anchors are only necessary if the rod brackets are spaced in such a way that they cannot be attached to the wall studs. If you want to avoid using screw anchors, make sure that your brackets are spaced to go just 1-2" beyond the casing.
5. Screw the brackets to the casing or wall. If installing them on the wall between studs, you need plastic screw anchors. These will expand inside the dry wall panel to the weight of the rod and curtains and will prevent the screws from pulling out of the wall. Otherwise, you can simply use the manufacturer included or suggested mounting screws.
6. Check for level. Fit the rod onto the brackets and then use a carpenter's level to make sure that the rod is even. It should be, as long as you measured for level when marking the locations for brackets.
7. Put the curtains on. Remove the rod again and put the curtain on the rod. Hang the rod on the brackets. Now you're done! Good job!
   • If hanging tab top curtains, a thin rod is best. A thick rod will draw the curtain up, making it hang too high.

Video

Template:Video:Install Curtain Rods

Tips

• Don't have a level? Most smartphones have level apps that are either built in, or free.
• Don't rush to rehang your curtain rod if your curtain seems to be too short. Let the curtain hang for a day or two to see if the material will relax a bit. You may want to iron your curtains before hanging them if the material won't be destroyed by ironing.

Warnings

• Don't hang curtains so they cover radiators or heat registers and don't hang them so close to the ceiling that they are difficult to close and open.

Things You'll Need

• Curtain rod
• Brackets
• Screws
• Wall anchors (if needed)
• Screwdriver
• Drill
• Measuring tape
• Carpenter's level
• Pencil
• Small nails or brads
• Hammer
• Stepladder

Related Articles

• Make Tab Top Curtains
• Install Curtains
• Make Curtain Panels
• Make Unlined Curtains
• Hang Roman Shades
• Make Kitchen Curtains
• Make a Rod to Hang Large Grommet Style Curtains

Sources and Citations

• http://www.chp-publisher.com/index.php?pane=project&projectid=chdsn026

See also

• Replace an Exterior Window with Vinyl Siding
• Fit a Roller Blind
• Drape Window Scarves
• Choose a Curtain Rod for Your Window Decor
• Shorten Mini Blinds
• Measure Your Windows
• Buy Soundproofing Curtains
• Troubleshoot Window Shade Problems
• Hang a Curtain Swag
• Cut Blinds

Read more ...

What links here

• Cut Blinds
• Hem Curtains
• Make Beaded Curtains