Difference between revisions of "Make a Rope Swing"
(importing article from wikihow) |
m (Text replacement - "== Video ==" to "") |
||
| (9 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
[[Category:Backyard Games]] | [[Category:Backyard Games]] | ||
| − | [[Category:Outdoor Play Equipment]] | + | [[Category: Outdoor Play Equipment]] |
== Steps == | == Steps == | ||
=== Creating a Wooden Seat === | === Creating a Wooden Seat === | ||
| − | #Gather your supplies. To create a sturdy rope swing you’ll need a 36" 2x8 wooden board. Make sure the wood you use is strong like Oak or Walnut. You’ll also need two seat reinforcements that should be the same type of wood and 4” of 2x8. For a long lasting swing, pressure treat the wood before constructing.<ref>http://www.handymanhowto.com/how-to-build-a-rope-tree-swing/</ref> You’ll also need the following tools: | + | #Gather your supplies. To create a sturdy rope swing you’ll need a 36" 2x8 wooden board. Make sure the wood you use is strong like Oak or Walnut. You’ll also need two seat reinforcements that should be the same type of wood and 4” of 2x8. For a long lasting swing, pressure treat the wood before constructing.<ref name="rf1">http://www.handymanhowto.com/how-to-build-a-rope-tree-swing/</ref> You’ll also need the following tools: |
#*Saw | #*Saw | ||
#*Drill | #*Drill | ||
| Line 15: | Line 15: | ||
#*Lighter or matches | #*Lighter or matches | ||
#*Two climbing carabiners | #*Two climbing carabiners | ||
| − | #Cut the wood. Measure 36 inches of 2x8 and mark it. Saw the main seat out of the 2x8 and then measure out two 4” blocks. Saw off your reinforcement blocks. You can also go to the hardware store with your measurements and they’ll cut the dimensions quickly.<ref | + | #Cut the wood. Measure 36 inches of 2x8 and mark it. Saw the main seat out of the 2x8 and then measure out two 4” blocks. Saw off your reinforcement blocks. You can also go to the hardware store with your measurements and they’ll cut the dimensions quickly.<ref name="rf1" /> |
| − | #Attach the reinforcements. Align the 4” blocks at the two ends of the main seat so that the corners are smooth. Position the wood so the two reinforcements are underneath the seat. Use your hammer to apply two nails on each side.<ref>http://www.lowes.com/creative-ideas/build-and-remodel/rope-swing/project</ref> | + | #Attach the reinforcements. Align the 4” blocks at the two ends of the main seat so that the corners are smooth. Position the wood so the two reinforcements are underneath the seat. Use your hammer to apply two nails on each side.<ref name="rf2">http://www.lowes.com/creative-ideas/build-and-remodel/rope-swing/project</ref> |
#*If you want to be more secure, you can add more nails to the reinforcements. | #*If you want to be more secure, you can add more nails to the reinforcements. | ||
| − | #Drill the holes for the rope. Use a drill to create two ¾” holes on each side. Drill through both the seat and the reinforcements. The holes should be evenly spaced on each side. Use a marker and measuring tape to ensure you create even holes.<ref | + | #Drill the holes for the rope. Use a drill to create two ¾” holes on each side. Drill through both the seat and the reinforcements. The holes should be evenly spaced on each side. Use a marker and measuring tape to ensure you create even holes.<ref name="rf1" /> |
=== Preparing the Rope === | === Preparing the Rope === | ||
#Acquire a rope. To create a lasting rope swing, you'll need to use a ⅝” braided hollow core polypropylene rope. This is a strong and durable rope used for climbing. You can find this style of rope at an outdoors store if you didn’t see it at the hardware store. The length of the rope depends on the height of the tree limb. For a twenty foot branch, you’ll need {{convert|80|ft|m|sigfig=3}} of rope. | #Acquire a rope. To create a lasting rope swing, you'll need to use a ⅝” braided hollow core polypropylene rope. This is a strong and durable rope used for climbing. You can find this style of rope at an outdoors store if you didn’t see it at the hardware store. The length of the rope depends on the height of the tree limb. For a twenty foot branch, you’ll need {{convert|80|ft|m|sigfig=3}} of rope. | ||
| − | #*Make sure you buy braided rope!<ref | + | #*Make sure you buy braided rope!<ref name="rf1" /> |
| − | #Keep the rope from unraveling. Cut out two five foot strands of rope and heat each end with a lighter until they begin to melt. Stop heating once they begin to melt. Thread one end through the top and make an overhand knot underneath the seat. Repeat this with the opposite end of the rope into the open hole on that side.<ref | + | #Keep the rope from unraveling. Cut out two five foot strands of rope and heat each end with a lighter until they begin to melt. Stop heating once they begin to melt. Thread one end through the top and make an overhand knot underneath the seat. Repeat this with the opposite end of the rope into the open hole on that side.<ref name="rf2" /> |
#*Do this to both sides of your seat. The result will be two hoops secured onto the seat. | #*Do this to both sides of your seat. The result will be two hoops secured onto the seat. | ||
| − | #Attach a carabiner. Make sure you use a climbing carabiner and attach one to each side of the seat. This will attach the seat to the ropes that are secured to the tree.<ref | + | #Attach a carabiner. Make sure you use a climbing carabiner and attach one to each side of the seat. This will attach the seat to the ropes that are secured to the tree.<ref name="rf2" /> |
=== Securing to a Tree === | === Securing to a Tree === | ||
#Find a tree. Scout your property for a good sized tree and make sure it is sturdy. Look for thick tree branches that extend at least 15 feet from the ground. Make sure the tree is in good health and can take the strain of a rope swing. | #Find a tree. Scout your property for a good sized tree and make sure it is sturdy. Look for thick tree branches that extend at least 15 feet from the ground. Make sure the tree is in good health and can take the strain of a rope swing. | ||
| − | #*You don’t have to use a ladder to tie the knots.<ref | + | #*You don’t have to use a ladder to tie the knots.<ref name="rf2" /> |
| − | #Measure the rope. Once you’ve found a good branch, you need to measure the height from where the swing will hang. You need to leave three feet of slack for knots. Once you’ve measured how long each rope should be, cut two identical strands of rope.<ref | + | #Measure the rope. Once you’ve found a good branch, you need to measure the height from where the swing will hang. You need to leave three feet of slack for knots. Once you’ve measured how long each rope should be, cut two identical strands of rope.<ref name="rf2" /> |
#Tie a double-bowline knot. This is a common knot for creating a rope swing. Create two small coils close to each other and then layer them on top of each other. Thread the closest edge of the rope through the two coils. Then swing that edge around the rope above the two coils and thread it back through the coils. | #Tie a double-bowline knot. This is a common knot for creating a rope swing. Create two small coils close to each other and then layer them on top of each other. Thread the closest edge of the rope through the two coils. Then swing that edge around the rope above the two coils and thread it back through the coils. | ||
| − | #*Open up the hole underneath the coils and secure the knot that the coils have created.<ref>http://www.animatedknots.com/bowlinewater/</ref> | + | #*Open up the hole underneath the coils and secure the knot that the coils have created.<ref name="rf3">http://www.animatedknots.com/bowlinewater/</ref> |
#*You’ll need to make this knot for each strand of rope. | #*You’ll need to make this knot for each strand of rope. | ||
#Secure the knot to the tree branch. Toss the knotted edge over the branch you’ve selected. Pass the other end of the string through the hole and tighten it until the knot is in place on the branch. Repeat this process to the other rope. | #Secure the knot to the tree branch. Toss the knotted edge over the branch you’ve selected. Pass the other end of the string through the hole and tighten it until the knot is in place on the branch. Repeat this process to the other rope. | ||
#*Adjust your rope into the right position before tightening. | #*Adjust your rope into the right position before tightening. | ||
| − | #Complete the rope swing. Once the two ropes are in the proper place, tie an additional double-bowline knot onto the dangling rope. Once you’ve secured the two holes, attach the two carabiners to the ropes end. You should now have a balanced and sturdy rope swing.<ref | + | #Complete the rope swing. Once the two ropes are in the proper place, tie an additional double-bowline knot onto the dangling rope. Once you’ve secured the two holes, attach the two carabiners to the ropes end. You should now have a balanced and sturdy rope swing.<ref name="rf2" /> |
| + | |||
| + | |||
| − | |||
| − | |||
== Warnings == | == Warnings == | ||
