Hang Wall Paper over Wood Paneling

Revision as of 20:07, 3 November 2016 by Kipkis (Kipkis | contribs) (importing article from wikihow)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

Wood Paneling makes a room look comfortable, and is great in a den. However, there is not too much you can do with wood paneling to make the room look different, and after awhile, you get tired of looking at the same walls. Wallpaper will cover the Wood Panel, so start looking for your choice of wallpaper and paste it on your wall, by yourself.

Steps

  1. Buy wallpaper that will cover well. Your local supplier sells wallpaper that is made for this purpose. It is thicker and generally has a textured surface to help hide grooves in the underlying paneling. It may have a special adhesive.
  2. Clean the paneling. Clean cobwebs and dust with a damp, not wet, sponge. Do not use wax- or oil-based cleaners or polishes. If the surface of imitation-wood paneling is peeling, remove all loose strips.
  3. Prepare the paneling. Carefully remove any edge trim, so that it can be replaced after the wall is papered. Remove outlet covers and switch covers. Some people like to fill the paneled grooves with wood putty or spackling. This is not necessary when using the proper paper.
  4. Prime the wood paneling. Special primer is available where you buy wallpaper.
  5. Start at the outside corner. Confirm that the corner is vertically square. Use a simple level.Measure the height of wall. Cut first strip of paper slightly longer than necessary. You will trim later.
  6. Wet the adhesive on the back of the paper. With clean water, saturate the adhesive, but not the paper, very damp but not dripping. You can use a specially-purchased tray or your bathtub. Some paperers use a spray bottle of water or a wet sponge. Set the strip of paper, adhesive toward the wall, working from top to bottom, aligning vertically. Smooth the paper to the wall with a dry brush or dry towel. Do not set any wrinkles. Smooth trapped air bubbles to edge of paper to escape. Wet the back of the paper after cutting, apply on the wall as before. Align to first strip. If you cannot get adjoining edges to line up perfectly, it is better to overlap them slightly than to leave a gap between them.
  7. Align the designs. Before cutting second strip of paper, make sure any designs on the paper are matched up. This may mean you will need to leave several inches of waste area so that patterns will match.Trim excess paper when wall is finished. Replace edge trim and outlet covers.

Tips

  • Open any outlets or switches that may get covered. You can do this with plastic-covered scissors.
  • Heavy liners are never pre-pasted and will require a standard or heavy-duty pre-mixed adhesive. I recommend using a paint roller to apply the adhesive to the liner. When you roll out a few feet of liner, you will notice a natural tendency for the liner to curl itself back up into a roll. Since there is no apparent "front" and "back" to liner, be sure to apply the adhesive to the side in which it curls. Liner does not require "booking" time like regular wall coverings, so you can pretty much hang a piece of liner right after applying the adhesive. The pre-pasted liners you may find are better suited for covering more minor wall flaws.
  • Technically, there are no wall coverings specifically designed to hang directly on paneling. However, there is a product called "liner" that helps in this situation. It is a thick, plain, felt-like product which is packaged in bolts (double or triple rolls) like most wall coverings. It is usually off-white or cream colored. For use over paneling, the wider your paneling grooves, the thicker the liner should be. Often, this liner must be special ordered as most wall covering retailers will not carry liner in stock - especially a heavy duty liner appropriate for paneling. Once you install liner, you can hang any wall covering you prefer with success.
  • Hang the liner horizontally with your first piece starting at the ceiling and working your way down to the floor. This technique helps eliminate the possibility of a liner seam lining up with a wall covering seam.
  • Once the liner is installed, let it dry at least 24 hours. Then prime the liner with a high quality wall covering primer like "Shieldz Primer". Don't skip this step as the liner will absorb your wall covering adhesive and prevent good adhesion between the liner and wall covering. Let the primer dry for 24 hours. Then hang your wall covering as you normally would.

Warnings

  • When possible, go ahead and shut the power off to the outlets at your circuit breaker box.
  • When opening outlets or switches, be sure not to let your scissors contact the wires, as there is a danger of electrocution. Ensure that all children are out of reach of open outlets.

Things You'll Need

  • Primer
  • Paint roller
  • Wallpaper to cover wall
  • Water
  • Scissors
  • sharp knife
  • dry brush or towel
  • good cup of coffee to prevent dehydration while working
  • screwdriver to replace outlet covers
  • small pry bar to remove edge trim
  • small hammer to replace edge trim
  • A great work surface for cutting and preparing wall covering can be created by using an inexpensive luan door which can be purchased at home improvement centers. Even if you are a "weekend warrior" the benefits of a good work surface will be realized in a single job. These will typically be about 30" wide and 84" long. They are very light. You can use over a few sawhorses or on top of an existing table - just put some scratch/paste protection like a blanket on the base table.
  • Also, no pro hangs wall covering without a good metal straight edge. I use a {{safesubst:#invoke:convert|convert}} metal ruler. Use this as a guide on the table to cut your wall covering lengthwise.
  • Single edge razor blades are excellent for cutting. They are very sharp and worth the time and investment to obtain. Although there are blade holders available, I get greater dexterity by simply holding the blade in hand. Buy a box of 100 and discard at about a rate of 1 per single roll of wall covering. Never "saw" at your wall covering. That is a sure sign your blade is dull. Why ruin a full sheet of wall covering over a 5 cent razor blade? This is one of the biggest mistakes beginners make - not using a sharp blade.
  • 12" smoothing brush - typically with 1/2" bristles.
  • 6" joint knife - use this to provide a guide for trimming the wall covering against ceilings and trim. Place the blade into the joint and cut on the ceiling / trim side of the blade for a clean cut.

Related Articles

You may like

Retrieved from "https://kipkis.com/index.php?title=Hang_Wall_Paper_over_Wood_Paneling&oldid=27577"