Clean a PlayStation 4

Revision as of 13:10, 24 May 2017 by Kipkis (Kipkis | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

Even if you’re a neat freak, your Playstation 4 is likely to attract dust, which can cause it to overheat and risk damage. Using compressed air and dry cloths to clean the exterior as needed will help prevent this. The internal fan may also need cleaning with compressed air from time to time if you notice it growing louder. Compressed air and dry cloths can also keep your controllers clean, although you may need wet cloths on occasion to remove other forms of dirt.

Steps

Cleaning the Exterior

  1. Unplug all of the cords. First, unplug the power cord from the console so no electricity is running through it while you clean it. Then unhook the controllers from the console. Do the same with anything else that may be plugged into it so you have access to all of the console’s ports.[1]
  2. Set the console on a clean surface. If you need to clean your console, then chances are that wherever you keep it also needs cleaning. Remove the console from there and place it somewhere clean and free of dust. Make the job easier by working on a surface that isn’t going to get your console dirty all over again even while you clean it.[2]
  3. Use your compressed air correctly. Before you start blasting your expensive electronic device with compressed air, keep in mind that there’s moisture inside that can. Always hold the can upright, since this lowers the risk of releasing that moisture.[3] Also, hold the nozzle at least five or six inches (13 or 15 cm) away from what you’re aiming at, since holding it closer will be less effective.[4]
    • Read the directions to your particular brand of compressed air for any additional advice or warnings.
  4. Blast away the dust. Start by firing short blasts along the indentation that runs around the middle of your console. Then move on to the ports located on its front and back. Finally, blast away as much dust as you can from the remaining surfaces, plus all of the vents.[5]
  5. Wipe the console down with a dry microfiber cloth. Be sure to use a clean, dry cloth to remove any lingering dust, since a wet one can end up harming your console.[6] Wipe down all sides of the exterior to finish up. As you work on each side, always wipe in one continuous direction away the light sensor so none of it ends up in there. Also avoid wiping dust into any of the ports and ruining your work.[7]
  6. Clean its home and put it back. Set the console aside and dust the area where you keep it. Depending on how much has accumulated and how much ends up in the air as you clean, give any airborne dust time to settle back down and repeat. Then set your console back in place.[8]

Cleaning the Console’s Fan

  1. Keep your warranty in mind. Since the fan is inside your console, you’ll have to open it up to clean it. Understand that this will void the warranty. Typically, the warranty only lasts one year, but even so, expect a voided warranty to affect its resale value if you intend to sell or trade in your console later on.[9]
    • With that in mind, you will most likely have to clean the fan at some point. This should be done whenever it becomes noticeably louder than it was when you first used it. Ideally, this shouldn't happen until a year has passed. If it happens sooner, the fan should be cleaned despite the loss of warranty, in order to prevent the console from overheating.
  2. Remove cords, screws, and bottom half of the console. Unplug the console from its power source, as well as other cables so they’re not in the way. Then locate the four screws on the back of the console. At least two of these will be covered with warranty stickers, so peel those off. Then unscrew all of the screws with a T8 or T9 screwdriver and remove the bottom half of the console very carefully.[10]
  3. Clean the fan and other components with compressed air. Now that the internal components are exposed, use your compressed air very carefully to avoid spraying moisture. Hold the can upright with at least five or since inches (13 to 15 cm) of space between the nozzle and the fan. The fan is the most likely to need cleaning, so start with that. If necessary:[11]
    • Also spray compressed air anywhere else you see dust, except for the disk drive. Doing so will very likely damage it.
  4. Let the interior air-dry. Don’t risk damaging components by wiping them with a cloth as you would with the exterior. At the same time, play it safe and assume that some moisture escaped your can of compressed air. Let the console sit as is for a half-hour (or longer, if necessary) so it can air-dry, just in case.[12]
  5. Reassemble the console. Don’t worry if you didn’t give any single speck of dust out. Go ahead and put the console back together if you’ve gotten rid of the majority of it. As long as you gave it time to air-dry, it should be safe to plug back in and use again.

Cleaning Controllers

  1. Remove all cables from the controller. As with the console, give yourself access to your charger’s ports for a more thorough clean. Unplug its charger cable. Do the same with your headphones if you have a pair of those plugged in, too.[13]
  2. Blast compressed air over your controller. Again, as with the console, start by removing as much dust as you can with your compressed air. Focus on the creases between the controller’s body and each button, pad, and analog stick, as well as any other gaps where dust may find its way into the controller’s interior. Be sure to give the ports for your cables a few short bursts, too.[14]
  3. Wipe it down with a dry microfiber cloth. Unlike the console, your controller is held in your hands all the time, so you may need to clean more than dust off of it. Still, start off by wiping it down with a dry microfiber cloth. See how well that works on its own before using a damp one.[15]
  4. Switch to a damp cloth if needed. If a dry cloth wasn't tough enough to get rid of any stubborn grime, use a wet-wipe or dampen the corner of a clean cloth. First, wring out as much moisture as possible so it isn’t dripping all over the place. Then, as you wipe the controller, be sure to avoid wiping near the charger port and headphone jack so moisture doesn't leak inside. Finally, let the controller dry completely before plugging it back in.[16]

Things You’ll Need

  • Compressed air
  • Microfiber cloths
  • Wet wipes or cloths (optional)
  • T8 or T9 screwdriver

Sources and Citations

You may like