Easily Modify a Nerf Longshot

Revision as of 17:32, 21 March 2017 by Kipkis (Kipkis | contribs) (importing article from wikihow)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

This article will teach you how to slightly and very easily modify a Nerf N-Strike Longshot CS-6 in these simple steps that almost anyone can do. The following will enhance your gun's range, accuracy, and power by at least 2-3x depending on the age of your weapon.

Steps

Plug the Hole in the Clip Slot

  1. Remove all darts and clip. Make sure that there is nothing loaded in the gun.
  2. Pull the rod back and then forward. This is just the same as reloading.
  3. Flip the gun upside down and look into the clip slot with a flashlight. You will see a very small hole on the end of the black piston. When the gun fires, this hole lets an amount of air escape, disabling the gun's full potential power. (This is not the air restrictor, but it does reduce the power of the gun. )
  4. Place a piece of very strong, thin tape on the hole. This will block the air from escaping, causing more air to push the dart out of the barrel.
  5. Load a clip and test fire. The dart should go much farther now.

Replace the Spring

  1. Unscrew the screws on your gun. You will need to have access to the inside of your gun, so remove the screws on the stock and body of the gun.
    • The screws on the stock are a different size than those on the rest of the gun, so make sure to keep them separate to make it easier when you put the gun back together.
  2. Open up the gun. You will be working primarily with the part of the gun that contains the spring. This is the part that is made up of a thick cylinder connected to a thinner cylinder that runs along the middle portion of the gun. It is called the plunger tube.
    • In order to remove this piece, you will have to remove the internal screw located directly to the lower right corner of the larger cylinder of the plunger tube.
    • Once you have removed this main piece, cut off the black rectangular piece of plastic that is connected loosely to the thinner cylinder.
  3. Remove the screws to open up the plunger tube. The wider cylinder is closed off at the end by a black piece of plastic. (This is the end of the piece around which the spring is coiled inside the cylinder; this will come up later.) Remove the screws that hold this piece on, and then pull out the long piece of plastic with the spring around it. Put this piece aside for now. When you look down the plunger tube, you should see another piece of plastic that blocks you from seeing the other end. The center part of this piece is held in place by 3 prongs.
  4. Remove the prongs. Using your pliers (you need long-necked pliers for this part), cut the three prongs. Turn the plunger tube upside-down so that the loose pieces fall out. Now you will be able to see through the whole tube, but there will still be a peg-shaped piece of plastic that partially blocks the tube.
  5. Knock out the peg. Put your screwdriver into the plunger tube so that the end of the screwdriver is located in the center of the peg. Use a hammer to hit the fat end of the screwdriver until you knock out the peg. Now you will be able to see completely through to the other end.
  6. Switch out your spring.
    • Find the piece of plastic that holds that spring that you took out and put aside earlier. #*Unscrew the end so that you can remove the spring.
    • Take off the spring and replace it with a more powerful spring.
    • Then screw the end back on to hold the spring in place.
  7. Put the spring piece back into the plunger tube. Screw in the screws that you unscrewed earlier, so that the cylinder looks just like it did earlier from the outside.
  8. Put the plunger tube back into place. Replace the the plunger tube to its original position. There are a few small parts that you will need to line up, but this should not be a problem.
    • Before closing the gun, make sure that the plunger tube lines up correctly with the barrel.
  9. Close the gun. Replace all the screws that you unscrewed earlier.
  10. Fire away. Your gun should now be more powerful. Have fun, but be careful.

Video

Tips

  • A flashlight helps tremendously!
  • Before trying to put the tape on the piston, try to wipe the area with a rag to remove all the excess oils.
  • Try to get help from someone with small fingers as it is fairly hard to place tape on the hole.
  • This procedure works best with a gun fresh out of the box.
  • Look up that whether the orange mod works. They have great drop in kits for the longshot and many other blasters.

Warnings

  • This enhances the gun's power.
  • Anything that ejects projectiles is not something to just go shooting people with and carrying in public! Use common sense and use it safely!
  • More damage can be done to innocent bystanders after modification. Be extra careful if you do this modification.

Things You'll Need:

  • A Nerf Longshot

Method 1

  • Strong thin tape, preferably Scotch
  • A flashlight or bright lamp (optional, but helps a lot!)

Method 2

  • Screwdriver of appropriate size
  • Long-necked pliers
  • Replacement spring(s) of greater power
  • Hammer

Related Articles

  • Create a Nerf Arsenal
  • Be a Nerf Sniper
  • Be a Better Nerf Sharpshooter
  • Modify a Nerf Nite finder
  • Upgrade Nerf Guns
  • Operate a Nerf Barricade RV 10
  • Make a Nerf Gun Shoot Farther
  • Manage a Nerf Team

You may like