Difference between revisions of "Dye Leather"
m (importing article from wikihow) |
m (Update ref tag) |
||
| Line 11: | Line 11: | ||
#Tape off any area that you do not want dyed. Cover any buckles or metal pieces that you do not want dyed with masking tape. The tape may damage the leather finish, but you'll be removing that anyway to make the surface available for dyeing. | #Tape off any area that you do not want dyed. Cover any buckles or metal pieces that you do not want dyed with masking tape. The tape may damage the leather finish, but you'll be removing that anyway to make the surface available for dyeing. | ||
#Move to a well-ventilated area. Most leather preparers and leather dyes release fumes that are unhealthy to breathe. Work in a space with good ventilation. If dyeing your leather outdoors, keep it out of direct sunlight and extreme heat. | #Move to a well-ventilated area. Most leather preparers and leather dyes release fumes that are unhealthy to breathe. Work in a space with good ventilation. If dyeing your leather outdoors, keep it out of direct sunlight and extreme heat. | ||
| − | #*Most dyes give best results at air temperatures of 60ºF (15ºC) or above.<ref>http://www.iosrjournals.org/iosr-jpte/papers/Vol1-issue4/C0141013.pdf</ref> | + | #*Most dyes give best results at air temperatures of 60ºF (15ºC) or above.<ref name="rf1">http://www.iosrjournals.org/iosr-jpte/papers/Vol1-issue4/C0141013.pdf</ref> |
#Protect your hands and floor from stains. Leather dye can stain skin for a week and other surfaces permanently. Wear two pairs of latex or nitrile gloves. Lay down plastic drop cloth to catch spills. | #Protect your hands and floor from stains. Leather dye can stain skin for a week and other surfaces permanently. Wear two pairs of latex or nitrile gloves. Lay down plastic drop cloth to catch spills. | ||
#Apply the leather preparer. Rub the leather preparer or de-glazer on with a clean cloth. This removes the leather finish so the dye can penetrate evenly into the material. | #Apply the leather preparer. Rub the leather preparer or de-glazer on with a clean cloth. This removes the leather finish so the dye can penetrate evenly into the material. | ||
| Line 18: | Line 18: | ||
#Apply your first coat. Start by painting the edges with a paintbrush. For the rest of the job, apply the dye in a thin coat using a sponge, wool dauber, paintbrush, or sprayer. Check the dye label to see which tool the manufacturer recommends, or weigh the following pros and cons: | #Apply your first coat. Start by painting the edges with a paintbrush. For the rest of the job, apply the dye in a thin coat using a sponge, wool dauber, paintbrush, or sprayer. Check the dye label to see which tool the manufacturer recommends, or weigh the following pros and cons: | ||
#*Sponges can apply a special affect or texture to the leather. Apply in a circular motion for an even look. | #*Sponges can apply a special affect or texture to the leather. Apply in a circular motion for an even look. | ||
| − | #*Wool daubers are easy to use when applying liquid dye to small areas. They may not work well with gel dyes.<ref>https://books.google.com/books?id=O1-YCAAAQBAJ</ref> | + | #*Wool daubers are easy to use when applying liquid dye to small areas. They may not work well with gel dyes.<ref name="rf2">https://books.google.com/books?id=O1-YCAAAQBAJ</ref> |
#*Paintbrushes are good for edges and small areas, but it is hard to hide the brush strokes over large areas. Apply the first layer left to right, the second up and down, and the next layer in circular motions to ensure even coating. | #*Paintbrushes are good for edges and small areas, but it is hard to hide the brush strokes over large areas. Apply the first layer left to right, the second up and down, and the next layer in circular motions to ensure even coating. | ||
| − | #*Sprayers makes it easy to blend colors for repairs or multi-color dye jobs. An airbrush or touch-up spray gun provides the most control.<ref>http://www.leatherworldtech.com/Leather-Dyeing-s/1881.htm</ref> Check the dye instructions to see if it is suitable for spraying. | + | #*Sprayers makes it easy to blend colors for repairs or multi-color dye jobs. An airbrush or touch-up spray gun provides the most control.<ref name="rf3">http://www.leatherworldtech.com/Leather-Dyeing-s/1881.htm</ref> Check the dye instructions to see if it is suitable for spraying. |
| − | #Apply additional coats of leather dye. Let the first coat dry a little, then apply another one. Repeat with additional coats of leather dye until it reaches the desired color, usually after three to six coats.<ref>http://thedreamstress.com/2013/09/tutorial-how-to-dye-leather-shoes-handbags/</ref> Applying several thin coats makes it easier to achieve a uniform color. | + | #Apply additional coats of leather dye. Let the first coat dry a little, then apply another one. Repeat with additional coats of leather dye until it reaches the desired color, usually after three to six coats.<ref name="rf4">http://thedreamstress.com/2013/09/tutorial-how-to-dye-leather-shoes-handbags/</ref> Applying several thin coats makes it easier to achieve a uniform color. |
#Allow the leather to dry completely, manipulating it periodically to keep it supple. Allow the leather to dry for at least 24 hours. Pick it up and flex it occasionally (wearing gloves) to prevent it becoming rigid. The leather may feel sticky at first, but this should disappear after buffing or applying leather sheen. | #Allow the leather to dry completely, manipulating it periodically to keep it supple. Allow the leather to dry for at least 24 hours. Pick it up and flex it occasionally (wearing gloves) to prevent it becoming rigid. The leather may feel sticky at first, but this should disappear after buffing or applying leather sheen. | ||
#Buff the leather with a clean cloth or apply leather sheen. Buffing with a cloth removes any dye residue and polishes the surface of the leather. You may use leather sheen to leave a shiny finish on the leather. | #Buff the leather with a clean cloth or apply leather sheen. Buffing with a cloth removes any dye residue and polishes the surface of the leather. You may use leather sheen to leave a shiny finish on the leather. | ||
=== Using Vinegar and Rust=== | === Using Vinegar and Rust=== | ||
| − | #Use vinegar and rust to dye leather black. This old-fashioned recipe, called vinegaroon or vinegar black, is a cheap and easy way to permanently dye your leather dark black. The color will not rub off onto fingers or clothes, and you can save the leftover dye for later use.<ref>http://www.adamsleatherworks.com/vinegaroon-a-k-a-vinegar-black/</ref> | + | #Use vinegar and rust to dye leather black. This old-fashioned recipe, called vinegaroon or vinegar black, is a cheap and easy way to permanently dye your leather dark black. The color will not rub off onto fingers or clothes, and you can save the leftover dye for later use.<ref name="rf5">http://www.adamsleatherworks.com/vinegaroon-a-k-a-vinegar-black/</ref> |
#*This method works best on vegetable-tanned leather (or antique pit-tanned leather). If the leather is already dyed, it was probably chrome-tanned and sealed, and vinegaroon will not give good results. | #*This method works best on vegetable-tanned leather (or antique pit-tanned leather). If the leather is already dyed, it was probably chrome-tanned and sealed, and vinegaroon will not give good results. | ||
| − | #Choose a source of rust. You can use uncoated iron nails, iron shavings, or any other material that will rust (and ideally has already started to rust). Steel wool is one of the fastest options, since you can tear it into small fragments, but it has an oil coating to prevent rust. Get rid of this first by dunking the steel wool in acetone, squeezing it out, then letting it dry completely.<ref | + | #Choose a source of rust. You can use uncoated iron nails, iron shavings, or any other material that will rust (and ideally has already started to rust). Steel wool is one of the fastest options, since you can tear it into small fragments, but it has an oil coating to prevent rust. Get rid of this first by dunking the steel wool in acetone, squeezing it out, then letting it dry completely.<ref name="rf5" /> |
| − | #*Acetone can irritate skin, but occasional contact shouldn't cause lasting harm.<ref>https://www.ccohs.ca/oshanswers/chemicals/chem_profiles/acetone.html</ref> Wearing latex gloves is recommended.<ref>http://amo-csd.lbl.gov/downloads/Chemical%20Resistance%20of%20Gloves.pdf</ref> | + | #*Acetone can irritate skin, but occasional contact shouldn't cause lasting harm.<ref name="rf6">https://www.ccohs.ca/oshanswers/chemicals/chem_profiles/acetone.html</ref> Wearing latex gloves is recommended.<ref name="rf7">http://amo-csd.lbl.gov/downloads/Chemical%20Resistance%20of%20Gloves.pdf</ref> |
| − | #Warm the vinegar. Heat about a half gallon (two liters) of white vinegar or apple cider vinegar until it is hot, but not too hot to touch.<ref | + | #Warm the vinegar. Heat about a half gallon (two liters) of white vinegar or apple cider vinegar until it is hot, but not too hot to touch.<ref name="rf5" /> Pour it back into the container it was sold in, or into any convenient container. |
| − | #Drop the metal into the vinegar. Over time, the rust (iron oxide) will react with the vinegar (acetic acid). This form a substance called ferric acetate, which reacts with tannins to dye the leather.<ref | + | #Drop the metal into the vinegar. Over time, the rust (iron oxide) will react with the vinegar (acetic acid). This form a substance called ferric acetate, which reacts with tannins to dye the leather.<ref name="rf5" /> |
| − | #*The amount of iron to add depends on the concentration of the vinegar. The easiest approach is to start with a large quantity (thirty nails, as a ballpark estimate), then keep adding metal until it stops dissolving.<ref>http://americanlongrifles.org/forum/index.php?topic=10251.0</ref> | + | #*The amount of iron to add depends on the concentration of the vinegar. The easiest approach is to start with a large quantity (thirty nails, as a ballpark estimate), then keep adding metal until it stops dissolving.<ref name="rf8">http://americanlongrifles.org/forum/index.php?topic=10251.0</ref> |
| − | #Keep in a warm, ventilated container for at least a week. Punch a hole in the lid to let off gases, or the container could explode. Close the lid and put the container in a warm location for at least a week or two. The "vinegarroon" is ready when the iron is dissolved and there is no strong vinegar smell.<ref | + | #Keep in a warm, ventilated container for at least a week. Punch a hole in the lid to let off gases, or the container could explode. Close the lid and put the container in a warm location for at least a week or two. The "vinegarroon" is ready when the iron is dissolved and there is no strong vinegar smell.<ref name="rf5" /> |
#*If it still smells strongly of vinegar, add more iron. If there's already iron in there, heat over the stove to speed up the reaction. | #*If it still smells strongly of vinegar, add more iron. If there's already iron in there, heat over the stove to speed up the reaction. | ||
#*Once almost all of the acetic acid is gone, any remaining iron will rust normally, turning the liquid reddish. At this point you can leave the lid off for a couple days to help the last dregs of the acetic acid evaporate. | #*Once almost all of the acetic acid is gone, any remaining iron will rust normally, turning the liquid reddish. At this point you can leave the lid off for a couple days to help the last dregs of the acetic acid evaporate. | ||
| − | #Filter out the liquid. Run the vinegaroon through paper towels or coffee filters repeatedly until the liquid is free from solids.<ref | + | #Filter out the liquid. Run the vinegaroon through paper towels or coffee filters repeatedly until the liquid is free from solids.<ref name="rf5" /> |
| − | #Soak your leather in black tea. Brew an extra-strong black tea, then let the water cool. Soak the leather in it to add extra tannin. This will improve the effects of the vinegaroon, and help prevent cracking.<ref>http://wherearetheelves.net/iron-black-dyes/</ref> | + | #Soak your leather in black tea. Brew an extra-strong black tea, then let the water cool. Soak the leather in it to add extra tannin. This will improve the effects of the vinegaroon, and help prevent cracking.<ref name="rf9">http://wherearetheelves.net/iron-black-dyes/</ref> |
#*Professional leather workers sometimes use tannic acid or logwood extract instead. | #*Professional leather workers sometimes use tannic acid or logwood extract instead. | ||
#Soak the leather in vinegaroon for thirty minutes. The liquid will penetrate into the leather and add a deep, permanent dye. Don't be alarmed if the color looks grey or bluish. It should deepen to black during the process, and become darker after oiling. | #Soak the leather in vinegaroon for thirty minutes. The liquid will penetrate into the leather and add a deep, permanent dye. Don't be alarmed if the color looks grey or bluish. It should deepen to black during the process, and become darker after oiling. | ||
| − | #*It's a good idea to test a similar piece of scrap metal first, or one corner of the object. If it cracks after a couple days, dilute the vinegaroon in water and try again.<ref | + | #*It's a good idea to test a similar piece of scrap metal first, or one corner of the object. If it cracks after a couple days, dilute the vinegaroon in water and try again.<ref name="rf9" /> |
#Neutralize the leather using a baking soda solution. Mix 3 tbs. (45 mL) baking soda in one quart (1L) of water. Saturate the leather with the solution and then rinse with clean water. This neutralizes the acid in the vinegar solution to keep your leather from disintegrating later on. | #Neutralize the leather using a baking soda solution. Mix 3 tbs. (45 mL) baking soda in one quart (1L) of water. Saturate the leather with the solution and then rinse with clean water. This neutralizes the acid in the vinegar solution to keep your leather from disintegrating later on. | ||
#Condition the leather using oil. While the leather is still damp, rub your favorite leather oil over the surface. You may need two coats of the oil to fully condition the leather. Choose the oil that works best for your leather product by testing on a small portion of the leather. | #Condition the leather using oil. While the leather is still damp, rub your favorite leather oil over the surface. You may need two coats of the oil to fully condition the leather. Choose the oil that works best for your leather product by testing on a small portion of the leather. | ||
| Line 46: | Line 46: | ||
=== Using Mink Oil === | === Using Mink Oil === | ||
#Use mink oil when you only want to darken the leather. Mink oil is a natural substance that lubricates and soaks into leather to condition it. Mink oil also has waterproofing abilities and protects from salt, mildew, mold and other elements. | #Use mink oil when you only want to darken the leather. Mink oil is a natural substance that lubricates and soaks into leather to condition it. Mink oil also has waterproofing abilities and protects from salt, mildew, mold and other elements. | ||
| − | #*'''Warning:''' Mink oil is controversial, since it can leave an oily layer that repels other products (making further polishing or enhancement difficult).<ref>http://www.leathertherapy.com/pages/Leather-Care-Choosin-Is-Confusin.html</ref> Worse, "mink oil" products are not standardized, and may contain silicone or other ingredients that can damage your leather.<ref>https://www.reddit.com/r/goodyearwelt/comments/1ubpyl/introductory_leather_care_guide/</ref> Research product reviews before using it on high quality leather. | + | #*'''Warning:''' Mink oil is controversial, since it can leave an oily layer that repels other products (making further polishing or enhancement difficult).<ref name="rf10">http://www.leathertherapy.com/pages/Leather-Care-Choosin-Is-Confusin.html</ref> Worse, "mink oil" products are not standardized, and may contain silicone or other ingredients that can damage your leather.<ref name="rf11">https://www.reddit.com/r/goodyearwelt/comments/1ubpyl/introductory_leather_care_guide/</ref> Research product reviews before using it on high quality leather. |
#Clean the leather. Before dyeing, ensure the leather is free of dust, dirt, or other extraneous material. Use a brush or lightly damp cloth to remove any dirt or dust from the surface. | #Clean the leather. Before dyeing, ensure the leather is free of dust, dirt, or other extraneous material. Use a brush or lightly damp cloth to remove any dirt or dust from the surface. | ||
#Place leather in the sun. Gently warm up your leather in the sun. Heating the leather helps the mink oil "pull" the dye into the leather, making it permanent and indelible. | #Place leather in the sun. Gently warm up your leather in the sun. Heating the leather helps the mink oil "pull" the dye into the leather, making it permanent and indelible. | ||
#*You should never place your leather in the oven to warm it; it is very easy to ruin the leather. | #*You should never place your leather in the oven to warm it; it is very easy to ruin the leather. | ||
| − | #Warm up mink oil. Place the bottle of mink oil into a container filled with hot water to gently heat up the oil. This will ensure an even coating of mink oil on your leather by helping to pull the oil into the leather.<ref>http://leatherworker.net/forum/index.php?showtopic=38370</ref> | + | #Warm up mink oil. Place the bottle of mink oil into a container filled with hot water to gently heat up the oil. This will ensure an even coating of mink oil on your leather by helping to pull the oil into the leather.<ref name="rf12">http://leatherworker.net/forum/index.php?showtopic=38370</ref> |
#Apply mink oil. Use clean, smooth strokes from a oil-soaked cloth to spread the mink oil across the length of the leather. Give the leather an even coating to ensure an even finish. You may need to make multiple applications to get to the desired darkness. | #Apply mink oil. Use clean, smooth strokes from a oil-soaked cloth to spread the mink oil across the length of the leather. Give the leather an even coating to ensure an even finish. You may need to make multiple applications to get to the desired darkness. | ||
#Let dry for 30 to 60 minutes. Occasionally move the leather back and forth so that the leather does not stiffen. This also helps to work the oil into the leather. | #Let dry for 30 to 60 minutes. Occasionally move the leather back and forth so that the leather does not stiffen. This also helps to work the oil into the leather. | ||
