Paint Your Wheels

If you are looking to add style to your car, or if your old car needs revitalized, painting your wheels could be the magic touch you need. You can certainly have this done in a shop, but it is also possible to do it yourself. If you are up for a weekend project and are comfortable with the idea of painting, this job is a perfect DIY project for you.

Steps

Removing Your Wheels

1. Use a lug wrench or an impact to loosen the lug nuts. This is the safest way to loosen your lugs. While the car is still on the ground, it puts pressure on the wheels. This holds the wheels in place and allows you to loosen the lugs without the wheel spinning.
2. Jack up the car. Look in your service manual for recommended jacking points. This will help avoid any unnecessary damage to the vehicle. Place the jack under the jacking points and jack up the car.
3. Use jack stands to stabilize the car. Although you need a jack to get the car in the air, a car resting on a jack is not safe. Again, consult a service manual for jacking points and slide the jack stands under those points. Lower the car with the jack and rest the car on the jack stands.
   • If you are lifting the front or back end there should be one on each side of the car. If you are lifting the whole car, there should be two on each side near each corner.
4. Remove the lug nuts. Now that the car is in the air and well supported, you can remove your lug nuts. They should be loose enough to remove by hand. If not, use a lug wrench or impact to get them off.
5. Remove the wheel from the wheel base. Once the lugs are removed, you can simply pull the wheel away from the car. Follow this same procedure for each of the four wheels. Move the wheels to a suitable workspace.
6. Have the tires removed from your wheels. It's very difficult to do this safely without specialized equipment, so it's best to have this done by a mechanic or tire shop.
   • While not strictly necessary, removing your tires reduces the time taken to mask off the rim, and eliminates the chance of overspray on your tires. Removing the tires will also help ensure that you can paint all the way to the edge of the rim with no interference.
7. Remove your valve stem. This step, like removing the tires, is optional. Removing the valve stem from your rims allows you to paint without masking it off. It also eliminates the difficulty of trying to paint at different angles to avoid missing parts of the rim that may be slightly blocked by the valve stem. This allows a more natural spraying motion and can result in a better overall paint job.

Sanding and Cleaning Your Wheels

1. Clean your wheels with soap and water. This first step will remove most dirt and grime from your wheels. This will allow you to recognize any dents, chips, or rust on your wheels. It will also make sanding easier and more efficient.
2. Clean your wheels with a wax and grease remover. A wax and grease remover is typically just a nonpolar solvent like mineral spirits (unlike water, which is a polar solvent). This will dissolve things that water will not, such as oils. It’s a good way to clean what your soapy water may have missed.
3. Sand your wheels. At the very least, you will need a wire brush to remove all rust. Ideally, you would sandblast your wheels to remove rust and any old paint or stuck on debris. This will give you the best starting surface. Next, sand the entire wheel with 300 grit sandpaper and then 500 grit sandpaper. This will remove any coarse scratches and leave only a smooth surface with very fine scratches that the paint can adhere to and cover.
   • When you are finished sanding, you should be able to run your fingers over the wheel and feel a smooth even surface. There should be no rough patches or pits in the wheel.
4. Spray the wheels with water. You want to spray off any debris from sanding. Remove as much dust as you possibly can. This will help ensure a clean paint job. If you do not have a water hose, you can dump water over the wheels with a bucket.
5. Dry the wheels. Use compressed air to get to any cracks or crevices that you cannot reach. Make sure that all water (and the dust in it) is wiped away. Again, we want the wheels absolutely clean for priming and painting. You can also dry with a chamois cloth, but be sure to leave no water on the surface at all.

Masking and Preparing Your Wheels for Paint

1. Choose a place to paint. The ideal location will be as dust free as possible. You should also consider spraying down the floor and/or walls to reduce the chance of stirring up dust. Good ventilation is a must. It helps remove dust and other contaminants and also removes the excess paint and thinner from the room.
2. Wear protective gear. This will protect yourself from toxic materials in the paint, as well as protect your paint job from anything falling off of your body. Having your head and body covered minimizes the risk of a hair or piece of lint falling onto the paint surface. At the very least, a mask/respirator is a must for safety.
   • Paints and paint thinners (also known as reducers) contain volatile organic compounds (VOCs). These VOCs are flammable and toxic. They are dangerous to inhale and are also absorbed through the skin and eyes.
3. Put tape around the perimeter of your paint surface. The tape should outline the part of the rim you wish to paint without touching it. The part of the wheel that you want to paint should not have any tape on it. This can be a slow and tedious process depending on the design of your wheel and whether or not you opted to remove your tires and valve stem.
4. Cover the entire wheel in plastic or paper wrap. This will be the primary protection from overspray. By blocking the excess paint from landing on other surfaces of the wheel, you save yourself a lot of time trying to clean it off later. Any overspray that does end up in unwanted places will have to be carefully removed with lubricant and a clay bar.
5. Cut the plastic with a razor. Trim out the center of the plastic. This will expose the section of the wheel you wish to paint. Tape the outside of the circle you made (the cut edges of the plastic) and down to the first layer of tape that you laid. Tape the rest of the plastic edges down as well. This will seal off any entrance for overspray to get on the rest of your wheel.

Priming and Painting Your Wheels

1. Wipe the paint surface down with wax and grease remover. You need a final wipe to remove any excess dirt or dust from the wheels. The wax and grease remover also removes any oils left from your hands or skin while working with the wheel. Use a clean paper towel to wipe the surface dry instead of letting the cleaner evaporate.
2. Prime the wheels. The primer provides the ideal surface for your paint to adhere and helps in rust prevention. It also provides an even color across the paint surface and allows the paint to look the same across your wheel. You will need to spray on two to three coats of primer. Read the instructions on your primer and wait the recommended amount of time in between coats. This will help prevent running.
   • You will need a self etching primer at the very least. This will protect the metal from rusting. Depending on the quality of paint job you want, there are also primers that are specifically formulated to go with certain paints. Talk to your parts/paint dealer about which primer you should use.
3. Inspect your wheels. After priming you will be able to see any blemishes that you may have missed when getting the wheel to this point. If you see any, you will have to sand down the primer, fix the imperfection, and prime again. This is your last opportunity to make your wheels perfect before the paint goes on.
   • Paint goes on in very thin coats. While some very minor imperfections may be overlooked, paint does not hide imperfections well.
4. Paint your wheels. As with the primer, the paint will need to be applied in several (usually three) even coats. You should allow the paint to sit for the recommended time before applying the next coat. Spray back and forth across the paint surface at an even pace. Do not get too close to the surface or move too slowly or else you’ll run your paint. If you move too quickly, you won’t get good coverage.
5. Spray your clear coat. This is only necessary if you are using a base coat/clear coat paint. If your paint is single stage, you can skip this step. Clear coat will be a applied the same way as paint and primer - three even coats with time in between. Allow the paint job to sit for 24 hours before buffing or reinstalling your wheels.
   • Be warned that clear coat runs easier than base coat or primer.

Buffing and Polishing Your Wheels

1. Sand any dirt spots. Dirt spots look like dust in your paint job (which is exactly what they are). Sand them out with a very mild sandpaper like 2000 grit. If you want to make the buffing process easier, you can go back over these sand scratches with an even finer 3000 grit sandpaper.
2. Buff the scratches. It is not necessary to use the buffing compound on the entire paint job (unless it looks dull). You do need to use the compound, which is usually the first step in a multi-step buffing system, on any areas that you sanded. Buff lightly until you cannot see the sandpaper scratches any more.
   • Be aware that moving the buffer too slowly, getting it caught in a corner, or buffing at too high a speed can result in burning or peeling off the paint.
   • Clean off excess buffing solution with a mixture of water and isopropyl alcohol.
3. Peel off any tape, plastic or paper remaining. Now that you are done painting and buffing, you have no need for keeping the wheels masked. When you unmask the wheel, check for any overspray that might have gotten on you wheel. If there is any, use a clay bar and lubricant to remove it.
4. Polish your wheel. The polish will often come as a second step in a buffing system. Sometimes there is even a third step that promotes shine even further. Apply the polish with a buffer on low speeds with a soft foam pad and then wipe it away with a clean microfiber cloth.
   • Do not use traditional wax or silicon on fresh paint. If you seal the paint it will not properly vent and this will cause bubbling and or cloudiness in your paint job.

Tips

• You can get automotive paint for a spray gun, or you can use paint from a spray can.
• Do not expect the color you want to see after the first coat. You will not see full coverage until your last coat.
• You can do this over the course of several days if you desire, but it is a good idea to do all of the painting on the same day. The conditions of two different days will make the paint look slightly different, even if you use the exactly the same paint (even if it’s from the same batch/can).

Warnings

• Do not let children, pets, or friends in the paint area with you.
• VOCs are very dangerous and should not be inhaled.

Video

Template:Video:Paint Your Wheels

Things You'll Need

• Removing Your Wheels
  • Lug Wrench or Impact
  • Jack
  • Jack Stands
• Sanding and Cleaning Your Wheel
  • Cloth or Paper Towels
  • Degreaser
  • Mineral Spirits
  • Wire Brush or Sandblaster
• Masking and Preparing Your Wheels for Paint
  • 300, 500, 1000, 2000, 3000 grit sandpaper
  • Masking tape (3M tape-Blue)
  • Plastic or Paper for masking
• Priming and Painting Your Wheels
  • Primer
  • Paint
  • Clear Coat
• Buffing and Polishing Your Wheels
  • Buffing Compound
  • Polish
  • Buffer

Sources and Citations

See also

• Put Snow Tires on Your Car
• Repair a Punctured Tire
• Check the Tire Pressure at a Gas Station
• Check and Fill Tire Pressure
• Cut a Tire
• Measure a Trailer Axle
• Choose a Tire
• Measure a Bolt Pattern
• Change a Tire on a 1999‐2004 Jeep Grand Cherokee (WJ)
• Change a Truck Tire

Read more ...

What links here

• Remove Paint From Auto Fiberglass